PLC-1 × 口口口 Optical splitter, PLC Splitter

HANGZHOU HUATAI OPTIC TECH. CO., LTD
	Product Classification

PLC-1 × 口口口
Multi-wavelength Planar Lightwave Circuit Splitter (PLC Splitter)

Technical index

1 × 口口口optical splitter index :

Performance		1x002	1x004	1x008	1x016	1x024	1x032	1x064	1x128
Fiber type		G.657.A
Working wavelength		1260~1650nm
Maximum insertion loss(dB)		≤ 4.2	≤7.4	≤10.7	≤13.9	≤15.8	≤17.2	≤20.4	≤23.7
Port insertion loss uniformity(dB)		≤0.6	≤0.6	≤0.8	≤1.0	≤1.0	≤1.5	≤1.8	≤2.0
Wavelength insertion loss uniformity(dB)		≤0.8	≤0.8	≤0.8	≤1.0	≤1.0	≤1.0	≤1.0	≤1.2
Return loss(dB)		≥55	≥55	≥55	≥55	≥55	≥55	≥55	≥55
Directivity(dB)		≥55	≥55	≥55	≥55	≥55	≥55	≥55	≥55
Package tyge	Bare fiber type	40×4×4			4×7×50			4×12×60	-
	Miniature type	50×4×4			60×7×4			6×12×80
	Model type	100×80×10			100×80×18			140×120×18
	Blade package type	130×100×25			130×100×50	-	130×100×100 or 260×100×50	130×100×200
	Tray type	288×180×25				-	288×180×50	288×180×100
	Rack-mounted type	483×342×44						483×230×88
Note 1: The insertion loss with plug optical connector increase less than 0.3dB base on above requirements, other indexes are the same; Note 2: The insertion loss of optical splitter with adapter ( include rack type, Tray type and Blade package type ) increase less than 0.2dB base on above requirements, other indexes are the same; Note 3: The maximum insertion loss in 1260~1300, 1600~1650nm wavelength range increase 0.3dB base on above requirements; Note 4: Splitting ratio performance index of 128 is tentative; Note 5: The working wavelength, insertion loss, return loss, directivity test method should according to Chapter Six of YD/T 1117-2001; Note 6: The test method of Wavelength insertion loss uniformity as below: input end input 1260~1650nm broadband lightl; source, output end switch in spectrum analyzer to measure the insertion loss that corresponding with wavelength, obtain the maximum and minimum of wavelength insertion loss.

Working environment index

Performance		Min.	Type	max
Working temperature	( ℃ )	-40	-	+85
Wavelength insertion loss uniformity(dB)	( ℃ )	-40	-	+85
Return loss(dB)	(Kpa)	62	-	106
Directivity(dB)	(%)	45	-	75

Environmental performance requirements

No.	Test item	Test method	Criterion
No.	Test item	Test method	Insertion loss variation	Appearance change after test
a	High temperature	85 ℃ (±2 ℃ ),duration time 96h,on-line test	≤0.4 dB	No mechanical damage in appearance, such as deformation, cracks, loose. No fiber fracture, fiber pull-out, fiber endpoint fault and cable seal damage etc.
b	Low temperature	-40 ℃ (±2 ℃ ),duration time 96h,on-line test	≤0.5 dB
c	dampness-heat	75 ℃ (±2 ℃ ),95%(±5%)RH, duration time 96h,on-line test	≤0.5 dB
d	Temperature cycling	( - 40 ℃ ~ + 85 ℃ ),one circulation 8h, 21 times circulation, on-line test	≤0.5 dB
e	Water soaking	Room temperature, tap-water, duration time 168h	≤0.3 dB
f	Salt fog	Saline solution: 5% NaCl, 6.5<PH<7.2; Temperature : 35°C duration time : 96 hours	≤0.3 dB
Note 1: Temperature circulation test will be the conversion curve shown as below, one circulation takes 8h,21 times.

Mechanical performance index

No.	Test item	Test method	Criterion
No.	Test item	Test method	Insertion loss variation	Appearance change after test
a	Drop test	Height:1.8m Times:3 axial direction,each 8 times Circulation:5 times	≤0.4dB	No mechanical damage in appearance, such as deformation, cracks, loose. No fiber fracture, fiber pull-out, fiber endpoint fault and cable seal damage etc.
b	Vibration test	Frequency:10~55Hz Scanning:45 time in a minute Amplitude:0.75mm Time:X, Y, Z direction each last 30min	≤0.5dB
c	Optical cable Torsion test	Load: Φ2.0mm optical cable: 15N Φ0.9mm optical cable: 4N Φ0.25mm optical cable: 2N Method:load point 22~28cm away from the plug, ±180⁰ torsion, 10 times/min, 25 times	≤0.4 dB
d	Optical cable tensile test	Load: Φ2.0mm optical cable: 50N Φ0.9mm optical cable: 4N Φ0.25mm optical cable: 2N Method: Plug side : load point 22 ~ 28cm away from the plug,2min; Packaging side: load point 22~28cm away from the packaging point,2min.	≤0.4 dB
Note 1 : Optical cable tensile test include optical cable plug side test and packaging side test .

Environmental lifetime index

No.	Test item	Test method	Criterion
No.	Test item	Test method	Insertion loss variation	Appearance change after test
a	High temperature storage(Dry)	85 ℃ (±2 ℃ ),or highest storage temperature Humidity<40%RH,duration time 2000h	≤0.5 dB	No mechanical damage in appearance, such as deformation , cracks, loose. No fiber fracture, fiber pull-out, fiber endpoint fault and cable seal damage etc.
b	Low temperature cycling	-40 ℃ (±5 ℃ ),or lowest st orage temperature,duration time 2000h	≤0.5 dB
c	dampness-heat	75 ℃ (±2 ℃ ), 90%(±5%)RH, or 85 ℃ (±2 ℃ ),85%(±5%)RH,duration time 500h(COa); 2000h(UNCb)	≤0.5 dB
d	Temperature cycling	( - 40 ℃ ~ + 85 ℃ ),one circulation 8h, 500 times	≤0.5 dB
Note 1: Temperature circulation test will be the conversion curve shown as below, one circulation takes 8h, 500 times.

Order explanation